Created with Sketch. Created with Sketch.
Tips to Making a Good Fabric Block

Tips to Making a Good Fabric Block

Posted by Carrie Newman on 22nd Mar 2019

TIPS to making a Good Quilting Block!


Everythingfabric©

Introduction

This is all about Good Habits! Like brushing your teeth. You want a nice finish on your project with all your points visible and no huge bumps where you have sewn your seams. These TIPs should help you in your process. I’ve chosen AUNT ELIZA’S STAR BLOCK to use in this example.

ACCURACY IN CUTTING.

There are marks on those rulers for a reason. Pick your cutting line which in this example is the 15” mark. Your Fabric and fabric pattern should be square.

Notice how on the Edge ruler the numbers 1- 4 line up perfectly with the inches on the mat. When you are cutting your fabric what you want to look at is that number 1 over the 14” mark on the mat. When you have that lined up on the bottom and the top on the other side of the fabric…you are ready to cut. I think when you go to cut it’s always best to trim your fabric this way first. Make sure it’s right. If you have a long piece, then fold in half. For the blocks we are doing nothing will be that long. (If you are left handed then the fabric would be to the right side of the ruler)

Accuracy in cutting your fabric

SEAMS

¼ “SEAMS are not as hard as they seem. Don’t be daunted by them because as soon as you master it a lot of your problems will be over

You have several ways of marking your fabric, with Frixion Pen, Pencil or anything like that. If you have a ¼” foot that’s a huge help. If you don’t you might consider getting one. Best investment ever! Now these photos show you my ¼” foot and the short seam I sewed.

IMG_0483



I laid my ruler on top so you can see it’s ¼” seam. If you have to draw that line, then do so. I buy my Frixion pens at Woollies. They iron out just as well as more expensive products.

There are different options out there but it works just as well for me

IMG_0516

SEAMS AND PRESSING

Should you fold over and press to the dark side or should you open flat and press?

Mostly always I will open flat and press. When you start a project you read the directions first. Have a look at the seam intersections. Do you have just 2 seams coming together or do you have 3 or 4 coming together?

For those of you who always press to the dark side when you flip over to the right side and iron you find those hard bumps that usually cause you to dirty up the fabric, twist up the seam and sometimes scorch it because it’s like trying to iron flat the Rocky Mountains! Not going to work.

You need to make that decision at the beginning. Once again this is very important and a must to get right now as it can impact your project later on




SEWING SECTIONS TOGETHER AND PINNING

Did you know there are different sized pins? Some are so much smaller like Dress Pins for example. If you would rather sew over the pins you use, then that is something to think about. See that pin? Right up the middle. Not to the left or right. But should be in between stitches in the middle of the seam and not sticking through fabric.

This is the correct way your pins should be placed




This is not the right way to do it







This is the correct way your pins should be placed

Yes, it is fiddly I know but it’s worth the time. Remember it’s about developing good habits. It’s important that both points going through are centred. Cause believe it or not if you have the point closet to the ball of the pin going through fabric you whole piece will be cockeyed! It really anchors it properly. Now some of you may have your needle in the opposite direction pointing in to the fabric. I just prefer mine this way.


MARKING FABRIC

Diagonal marking is from point to point. Not side of point. So put your marker point on one corner point if you need to and then set your ruler next to it. Mark your solid line. If you don’t have machine ¼” foot and need to mark your ¼” lines, then do so like I did in the example below with a dash line. The solid line is for cutting.

The photo below is a good example of when it’s not right. That line of holes on the top side of the solid line was my first sewing line that wasn’t right. I looked at it and knew it wasn’t right so I picked it out and resewed it. Before cutting I made my other diagonal line.












You can see the waviness came out once it was cut.








NOW FOR PRESSING!!

First…with your cut pieces closed press the seam to set it. Then open flat and press. Gently because these are bias cuts on those triangles and you don’t want to stretch them out.

YEP…STARCH!!! Give them a spray and press.

IMG_0504

Now to sew these together. Same as before These are small and one pin centre in the seam should be fine. Sew slowly. Don’t sew fast. Control it. I don’t remove the pins. Sew slowly over them.

Only one pin is needed. You put the first section under the needle, the centre is pinned and you hold the end closest to you. It’s short pieces and easy to control. Over 7 or 8 inches and up you might want to use another pin each side.

IMG_0507

When you have sewn all your triangle pieces together and you have your four squares this would be a good time to clip those dog ears. Don’t touch the square…just the little dog ears. You don’t need em throwing you off Sewing your ”seams together and certainly don’t need the extra bulk in your seams.







SEWING SECTIONS TOGETHER.

If you need to …two pins are plenty. Too many and they can make the whole process more difficult and cause distortion to the bias edges. NOTICE FLAT SEAMS. Sew slowly. This isn’t a race!

IMG_0508

IMG_0509Here are two longer pieces and you can see where I have put needles into the joint areas CENTRED in the seam only. Now if you sew slowly enough to maintain good control these distances between pins are short. A firm press with your fingers should be fine. I’m not against pins at all. I use them all the time. But they can make things more difficult sometimes than they need to be. Don’t rush and speed. Let me know how you go!

When I opened up look what I found! Those points shouldn’t be back so far. Unpicked and did it again.

FINISHED! Front and Back. Sides not even…don’t worry about that. It will become part of the seam when the time comes to sew the quilt together.

Lessons learnt?

  • CUT ACCURATELY SO YOU CAN SEW THAT ¼ INCH SEAM,
  • PRESS SO YOU HAVE A FLAT PIECE TO PIN YOUR SECTIONS TOGETHER.

IN THE END YOU'LL HAVE A BEAUTIFUL FLAT BLOCK! YAHOO YOU HAVE DONE IT!!!

I welcome comments on this tutorial good or bad! Please complete the feedback form. If you want a pdf copy please email me and request it and ill do my best to get it to you as soon as I'm able, Happy Quilting !